Speaker Test
A quick sound test for speakers and headphones. Check left and right channels, stereo phase, bass and 5.1 or 7.1 surround sound, or let your mic confirm your speakers work.
Click a speaker to play it
Phase (polarity) test
In phase should sound centred and full. Out of phase should sound wide, hollow and thin. If it’s the other way round, one speaker’s wires are swapped.
Bass and frequency sweep
A smooth 20 Hz to 20 kHz sweep. Listen for rattles, buzzing or where the sound fades out. Start at a low volume.
Mic and speaker check
Plays short beeps from each speaker and listens with your microphone. Take off headphones and turn the volume up.
- MicrophoneNot tested yet
- Left speaker heardNot tested yet
- Right speaker heardNot tested yet
How to test your speakers
- 1
Set a safe volume
Start with your system volume low. You can turn it up once you hear the first sound.
- 2
Play left and right
Press Left and Right. Each sound should come only from that side.
- 3
Check the phase
Play In phase, then Out of phase. In phase should sound centred and fuller.
- 4
Sweep the range
Play the sweep to hear how deep your bass goes and spot any rattles.
What each speaker test tells you
| Test | What you should hear | If it’s wrong |
|---|---|---|
| Left and right | Sound from one side only | Swapped: cables or headphones reversed. Silent side: cable, balance or power |
| Phase | In phase: centred, full bass. Out of phase: wide, thin | Reversed: swap + and − on one speaker |
| Sweep (20 Hz–20 kHz) | A smooth rising tone that fades in at the bottom and out at the top | Buzz or rattle at a pitch: loose panel, grille or object nearby |
| Surround (5.1/7.1) | Each sound from the speaker shown, going round the room | Wrong place: swapped wires or receiver settings. Silence: output not set to 5.1/7.1 |
| Mic and speaker | Both speakers “heard” by your microphone | Not heard: speaker off, volume low, or headphones in use |
Most laptop and phone speakers produce little below about 150 Hz, and most adults stop hearing the sweep somewhere between 12 and 17 kHz. Both are normal.
Surround sound test: 5.1 and 7.1
A browser can only send separate surround channels if your computer outputs them. This test checks how many channels the browser actually gets and tells you if surround isn’t available, instead of faking it with stereo panning.
- Windows: open Settings > System > Sound > More sound settings, select your HDMI or USB output, click Configure and choose 5.1 or 7.1 Surround. Turn spatial sound off for that device, then reload this page in Chrome, Edge or Firefox.
- Mac: open Audio MIDI Setup > your output > Configure Speakers > Multichannel, and pick 5.1 or 7.1.
- AV receiver: make sure the input isn’t set to a stereo or “all channel stereo” mode, which spreads two channels over every speaker.
Speaker layout guide
| Speaker | Position |
|---|---|
| Front left and right | 22–30° either side of the screen, at ear height |
| Center | Directly above or below the screen |
| Subwoofer (LFE) | Anywhere at the front; try a corner for more bass |
| Surround (5.1) | 110–120° either side, slightly above ear height |
| Side (7.1) | 90–110° either side of the listening position |
| Back (7.1) | 135–150° either side, behind the listener |
Angles follow the ITU-R BS.775 and Dolby layout recommendations.
Speakers not working? Common fixes
No sound at all
- Check the volume and mute on your device, the speakers themselves, and the browser tab (right-click the tab).
- Choose the right output in your system sound settings: speakers, headphones, HDMI monitor or Bluetooth.
- Make sure powered speakers are switched on and their own volume knob is up.
Sound only on one side
- Check the balance slider: Windows Sound settings > your device > Properties, or Mac System Settings > Sound > Output.
- Turn off Mono audio in accessibility settings if both sides play the same thing.
- Try another cable, or swap the left and right cables to see whether the fault follows the cable or the speaker.
Left and right are swapped
- Swap the cables at the amplifier or the speakers.
- For headphones, check the L and R markings and any “swap channels” option in your audio software.
Bluetooth speakers or earbuds
- Bluetooth adds delay, so sounds start a moment late. That’s normal.
- If quality drops while your mic is on, your device switched to hands-free mode. Use a separate microphone for calls.
Want to know how loud your speakers really are? Measure them in decibels with the sound level meter, and keep long listening sessions below 85 dB. Testing a call setup? Try the mic test and webcam test.
More free device tests
Frequently asked questions
How do I test my left and right speakers?
Press Left, then Right, or click each speaker in the diagram. The sound should come only from that side. If the left sound comes from the right, your speakers or headphones are swapped; if one side is silent, check that speaker’s cable, the balance setting in your system sound settings, and the speaker’s own power and volume.
Can I use this as a headphone left/right test?
Yes. Put your headphones on and press Left and Right. Most headphones mark the left side with an L or a raised dot. If the sides are reversed, check that you are wearing them the right way round and that no “swap channels” or mono audio setting is turned on.
How do I do a 5.1 or 7.1 surround sound test?
Choose 5.1 or 7.1 and press Test all speakers. Each speaker plays in turn, going round the room, and the subwoofer plays last. For this to work, your computer must output true 5.1 or 7.1: set it in your system sound settings, and use Chrome, Edge or Firefox on Windows. If the browser only gets two channels, the test tells you so rather than faking it.
What is the speaker phase test for?
It checks that both speakers push and pull together. Played in phase, sound seems to come from a point in the middle with solid bass. Played out of phase, it sounds wide, hollow and lacks bass. If “In phase” sounds hollow, the + and − wires on one speaker are reversed.
How do I test my mic and speakers together?
Use Mic and speaker check. It plays short beeps from the left and then the right speaker and listens for them with your microphone, so you know both work without needing a second person. Take off headphones first, because the microphone can’t hear them.
Why is there no sound in the speaker test?
Check that your device isn’t muted and the volume is up, that the right output (speakers, headphones, HDMI or Bluetooth) is selected in your system sound settings, and that the browser tab isn’t muted. On iPhone, turn up the media volume, and on older iOS versions switch off silent mode.
Is the frequency sweep safe for my speakers?
Yes at normal listening levels. Start with the volume low and turn it up gradually: very low bass and very high frequencies need far more power to sound loud, and small speakers can’t reproduce the lowest notes. Stop the sweep if you hear distortion.